Program car key fob (Toyota Kluger / Prado / RAV4)

May 29, 2022

Note: To check correct key for your car you can pop open your existing key case cover and check number stamped be on remote part number should be “50171” and “42050” Remote Programming: STEP1. Open Driver side door STEP 2. Put the Original key in and out of ignition for 2 times STEP 3. Close […]

Clear coat repair

May 29, 2022

The proper way to do it is sand back all the clear coat of affected panels. Use wet 800 or 1000 grit. Keep sanding until your sandpaper starts getting some of your car’s colour on it, then you know to stop because all the clear coat has gone. You will need to spray at least […]

Bench

May 17, 2022

Measured dining table height 77cm. Measured kitchen bench height 92cm. Measured barstool electronics bench height 100cm. I chose not to do miters as I may slide a smaller piece of metal into the open ends to create a vice / table extension or something (or not).  I did cap the bottom of the legs. Work […]

Drill press (a.k.a. column drill or pillar drill)

May 15, 2022

Unfortunately the beat-up cross slide vice that could be used for milling operations was not included and sold separately for more than I was willing to pay for it. https://www.instructables.com/Changing-Speeds-on-the-12-speed-Drill-Press/ A25 + A28 V belts.  SKF bearings. Tip: remove 2 of the 3 handles. If you want to use a drill press for milling, you […]

HVLP spray painting

May 15, 2022

Checklist – paint station work area outside (table). – general purpose paint thinner. – packet of flat wooden stir sticks (knives, paddle pop sticks, etc.) – plastic disposable yoghurt container (large enough to hold pot lid) for paint thinner. – glass 20cm tall jar (apple sauce / gherkins) with wide opening and airtight lid to […]

Measurements

May 13, 2022

box 58×28 bottom plank 58×20 top plank 58×15 backing board top 61×10 backing board bottom 50×28 sides x2 plywood (3x 360 spacing and 2x 60 to edge) 1140 screw 780 screw 420 screw 60 screw plasterboard ~0 screw 200 glue 400 screw 600 glue 800 screw 1000 glue ~1200 screw

Coolant Jug V1

April 29, 2022

Thank you masterxeon1001 ! https://www.youtube.com/user/masterxeon1001/videos Buy masterxeon1001 a beer! https://gumroad.com/masterxeon1001 (click on the Donate Box, enter an amount and pay using Paypal) Requirements Blender Get it here: https://builder.blender.org/download HardOps BoxCutter Get it here: https://blendermarket.com or https://gumroad.com Source Files coolant_jug_V1_001.blend coolant_jug_V1_002.blend coolant_jug_V1_003.blend Render

Oil Jug V2

April 25, 2022

Thank you masterxeon1001 ! https://www.youtube.com/user/masterxeon1001/videos Buy masterxeon1001 a beer! https://gumroad.com/masterxeon1001 (click on the Donate Box, enter an amount and pay using Paypal) Requirements Blender Get it here: https://builder.blender.org/download HardOps BoxCutter Get it here: https://blendermarket.com or https://gumroad.com Source Files oil_jug_V2_001.blend oil_jug_V2_002.blend oil_jug_V2_003.blend oil_jug_V2_004.blend oil_jug_V2_005.blend Render Low Poly High Poly Notes Adding detail after hardening edges and having max low poly […]

Oil Jug V1

April 23, 2022

Thank you masterxeon1001 ! https://www.youtube.com/user/masterxeon1001/videos Buy masterxeon1001 a beer! https://gumroad.com/masterxeon1001 (click on the Donate Box, enter an amount and pay using Paypal) Requirements Blender Get it here: https://builder.blender.org/download HardOps BoxCutter Get it here: https://blendermarket.com or https://gumroad.com Source Files oil_jug_V1_001.blend oil_jug_V1_002.blend oil_jug_V1_003.blend oil_jug_V1_004.blend Render     Notes Start by blocking out basic 3D shapes using ngon to follow the contours […]

Laundry Jug V1

April 18, 2022

Thank you masterxeon1001 ! https://www.youtube.com/user/masterxeon1001/videos Buy masterxeon1001 a beer! https://gumroad.com/masterxeon1001 (click on the Donate Box, enter an amount and pay using Paypal) Requirements Blender Get it here: https://builder.blender.org/download HardOps BoxCutter Get it here: https://blendermarket.com or https://gumroad.com Source laundry_jug_V1_001.blend laundry_jug_V1_002.blend laundry_jug_V1_003/blend Render Low poly High poly   Notes BisectMod is your friend. Adding additional edge loops (CTRL+R) is easiest if […]