3Com 5500-EI 28-Port + Airport Extreme
August 17, 2022
3Com For reference the default console only (!) credentials for 3COM/HP switches: user: admin password:<empty> user: manager password:manager user: monitor password:monitor Serial console connection 19200 baud <CTRL-B> 7 – Skip current configuration file (Y) 0 – Reboot Switch will boot from default boot option (firmware) but skip the startup config.file. This will allow administrator user […]
Protected: 2012 Nissan Navara D22 Dual Cab ST-R (4×4) 2.5 CR
July 23, 2022
There is no excerpt because this is a protected post.
Strategy
July 15, 2022
Alice came to the fork in the road. “Which road do I take?” she asked. “Where do you want to go?” responded the Cheshire cat. “I don’t know,” Alice answered.“ Then,” said the cat, “it doesn’t matter. Strategy is a high level plan to achieve one or more goals under conditions of uncertainty. […]
Agile / Servant Leader
July 4, 2022
“The focus in an agile project is on continuous learning and improvement.” Fail early Fail often Revise Learn Agile – Values PRIMARY Individuals and interactions Working software Customer collaboration Responding to change SECONDARY Processes and tools Comprehensive documentation Contract negotiation Following a plan Agile – Principles Satisfy the customer Welcome change Deliver software frequently Work […]
Program car key fob (Toyota Kluger / Prado / RAV4)
May 29, 2022
Note: To check correct key for your car you can pop open your existing key case cover and check number stamped be on remote part number should be “50171” and “42050” Remote Programming: STEP1. Open Driver side door STEP 2. Put the Original key in and out of ignition for 2 times STEP 3. Close […]
Clear coat repair
May 29, 2022
The proper way to do it is sand back all the clear coat of affected panels. Use wet 800 or 1000 grit. Keep sanding until your sandpaper starts getting some of your car’s colour on it, then you know to stop because all the clear coat has gone. You will need to spray at least […]
Bench
May 17, 2022
Measured dining table height 77cm. Measured kitchen bench height 92cm. Measured barstool electronics bench height 100cm. I chose not to do miters as I may slide a smaller piece of metal into the open ends to create a vice / table extension or something (or not). I did cap the bottom of the legs. Work […]
Drill press (a.k.a. column drill or pillar drill)
May 15, 2022
Unfortunately the beat-up cross slide vice that could be used for milling operations was not included and sold separately for more than I was willing to pay for it. https://www.instructables.com/Changing-Speeds-on-the-12-speed-Drill-Press/ A25 + A28 V belts. SKF bearings. Tip: remove 2 of the 3 handles. If you want to use a drill press for milling, you […]
HVLP spray painting
May 15, 2022
Checklist – paint station work area outside (table). – general purpose paint thinner. – packet of flat wooden stir sticks (knives, paddle pop sticks, etc.) – plastic disposable yoghurt container (large enough to hold pot lid) for paint thinner. – glass 20cm tall jar (apple sauce / gherkins) with wide opening and airtight lid to […]
Measurements
May 13, 2022
box 58×28 bottom plank 58×20 top plank 58×15 backing board top 61×10 backing board bottom 50×28 sides x2 plywood (3x 360 spacing and 2x 60 to edge) 1140 screw 780 screw 420 screw 60 screw plasterboard ~0 screw 200 glue 400 screw 600 glue 800 screw 1000 glue ~1200 screw